RADVision SCOPIA XT4000 Series Installationsanleitung

Installation GuideVersion 3.0SCOPIA XT4000 Series

Figure 2-1 SCOPIA XT Series as EndpointsPlanning NAT and Firewall Traversal with SCOPIA XT Series SCOPIA XT Series fully supports NAT and firewall t

Figure 2-2 Using an HTTP/STUN Server for NAT and Firewall TraversalThis approach works well in simple NAT and firewall traversal deployments, typicall

Figure 2-3 Using a NAT and Firewall Traversal ServerConfigure the traversal server as the XT Codec Unit gatekeeper and enable the H.460option. Configu

Figure 2-4 Using XT Series for NAT and Firewall TraversalThere are two possible setups in the GLAN1 and GLAN2 configuration (see Figure 2-4 onpage 8):

Supporting ISDN Connectivity The SCOPIA XT Series supports ISDN connectivity, allowing calls from endpoints to be routed tothe relevant conference u

Before beginning the installation of the system, you must read the safety regulations for asafe use of the system, verify the conference room setup, a

Place the camera(s) in a position to ensure eye contact between local and remoteparticipants. Recommended position is either directly below or directl

For a list of package contents see the invoice shipped with your order.Report any damage or missing items to your distributor or reseller.Keep the pac

After reading the section “Prerequisites for Setting up the System” on page 10, you can installthe SCOPIA XT Series. These sections describe how to in

Connecting SCOPIA XT Series For operational information about connecting SCOPIA XT5000 Series, refer to the Quick SetupGuide for SCOPIA XT5000 Serie

© 2000-2012 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd and areprotected by United States copyright

Figure 4-2 Connecting the XT Codec Unit to a private and a public networkwith multiple routers in both networksConnecting the Audio Equipment These s

Figure 4-3 Microphone SetupProcedureConnect the Microphone Pod output to the rear panel of the XT Codec Unit.RADVISION | Installation Guide for SCOP

Figure 4-4 Connecting the Microphone Pods to the XT Codec Unit of SCOPIAXT4000 SeriesConnecting an External Microphone System When the two-pod config

Connecting Analog Stereo Audio Equipment to the Analog Connector You can connect analog audio equipment to the stereo analog connector of the XT Cod

Connecting the Video Equipment These sections describe how to connect the video devices to the XT Codec Unit.•Connecting the Main XT Standard II Cam

Figure 4-6 Connecting the XT Standard II Camera for XT5000 SeriesConnecting the Optional XT Standard II Camera The XT Standard II Camera kit contains

Figure 4-7 Connecting the optional XT Standard II Camera for SCOPIAXT5000 SeriesStep 3Connect the power supply cable to the DC IN connector on the cam

through the VISCA interface. For this type of setup, enable the Always power on camera fieldin Administrator settings > I/O Inputs > Cameras.Pro

Be aware that SCOPIA XT Series supports HDCP (High-bandwidth Digital Content Protection).As an HDCP Licensee, you may not use a digitally protected co

Connecting the Computer You need a computer to share a presentation during a call. This procedure describes how toconnect computers that are equippe

1About the SCOPIA XT Series 2Planning the Topology of the SCOPIA XT Series Deployment Using SCOPIA XT Series as Endpoints...

Installing the Batteries of the XT Remote Control Unit When the XT Remote Control Unit's battery power is low, an icon appears on the GUI letti

After connecting the system and powering it, perform the initial configuration as described inthese sections:•Registering the SCOPIA XT Series to Obta

You can find the user code (and the serial number) by selecting Configure > About from theMain menu.Step 3On a computer, open a browser and navigat

ProcedureStep 1Open the envelope that you obtained when you bought your license extension, or refer to theemail you received after purchasing the lice

Figure 5-1 Enabling remote access to the SCOPIA XT SeriesStep 3Set the fields as required.Table 5-2 Enabling remote upgradeField Name DescriptionDownl

•Adjusting the Image Position... page 31•Configuring Network Settings...

Figure 5-2 Setting Country and LanguageStep 2Select the required country from the Country list using the arrow keys and press .The system menu and the

Figure 5-3 Examining the image positionStep 2Press 1 to align the top left corner.Figure 5-4 Adjusting the image positionStep 3Use the arrow keys on t

Configuring Network Settings This page allows you to setup the GLAN1 settings and the IP address the system uses forplacing a call.Consult with your

Before you beginThis procedure is performed as part of the basic configuration after “Configuring NetworkSettings” on page 33.ProcedureStep 1Set the E

Connecting Analog Stereo Audio Equipment to the Analog Connector... 18Connecting the Video Equipment...

Step 2Select the Administrator Settings tab.Step 3Select Utilities in the left pane.Step 4Select Administrator or User under Password.Figure 5-7 The U

ProcedureStep 1Access the SCOPIA XT Series web interface.Step 2In the Administrator Settings tab, select System > Date & Time > General on t

Table 5-4 Configuring time zone related settingsField Name DescriptionSelect the time zone to which the system belongs.Enable daylight time Set the da

Table 5-5 Configuring regional informationField Name DescriptionSystem name Enter the name that will appear in the local endpoint GUI and in theremote

Figure 5-8 Setting the XT Remote Control Unit CodeStep 3Enter the code in the Remote control code field.Step 4Select Save.Step 5On the XT Remote Contr

Figure 5-9 Settings general user settingsStep 3Select Yes from the Automatic screensaver list.Step 4Set the time after which the screen saver automati

Figure 5-10 Configuring general camera settingsStep 3Configure settings on the General page as described in Table 5-6 on page 41.Table 5-6 Configuring

Step 5To configure the main camera connection: configure settings on the HD1 page as described in Table 5-7 on page 43, and then select Save.a. Select

Table 5-7 Configuring advanced camera settingsField Name DescriptionEnable (this fieldappears on the HD2and DVI pages only)Enable for the optional cam

Figure 5-12 Configuring the computer settingsStep 3Select Yes from the Enable list to enable the DVI input.Step 4Select Save.Setting up the Monitor Di

Configuring Audio Outputs...53Configuring Network Settings...

•PaP (Picture and Picture) displays two images side-by-side on one monitor, where theremote image and the local image have the same size, emulating a

Table 5-8 Configuring general monitor settingsField Name DescriptionNumber of monitors Specifies the number of monitors connected to the XT Codec Unit

Step 7If necessary, adjust the way the image appears on the monitor:a. Select the monitor requiring adjustment (HD1 or HD2).b. Select Graphic adjustme

Table 5-9 Configuring PIP-PaP optionField Name DescriptionMulti Image Mode Sets PIP and PaP activation, depending on the number of videostreams availa

•Configuring Analog Audio Connections... page 50•Configuring the Echo Canceller ...

Table 5-10 Configuring the Microphone Pod connectionField Name DescriptionEnabled Enables/disables the Microphone Pod.Gain Use the slider to adjust th

Field Name DescriptionEnabled Enables/disables this audio input.Gain Set the voice signal to the desired level by using the slider.Echo canceller Enab

Configuring the Echo Canceller If your SCOPIA XT Series works with an external microphone system that does not contain echocancellation, perform thi

Table 5-11 Configuring echo canceller related settingsField Name DescriptionAGC Enables/disables Automatic Gain Control. The AGC reduces thevolume if

•If you are showing a presentation on your computer and it includes sound, route the soundof the computer to the analog input connector.Figure 5-18 De

The SCOPIA XT Series incorporates the latest state-of-the-art video technology for room highdefinition (HD) conferencing, including support for dual s

Step 3Set the fields as required.Table 5-12 Configuring audio output settingsField Name DescriptionDigital Audio to output If enabled, it routes the d

•Configuring IP Addresses... page 56•Configuring Network Connectivity ...

Step 8Select Addresses under GLAN.Figure 5-20 Configuring IP addressesStep 9Set the fields as described in Table 5-13 on page 57.Table 5-13 Configurin

Configuring Network Connectivity If necessary you can configure the GLAN1 and GLAN2 ports. The GLAN2 port is available only ifit is enabled. For mor

Table 5-14 Configuring network connectivityField Name SettingMTU Sets the maximum size of each IP packet the XT Codec Unit cansend to the network.If t

Figure 5-22 Configuring NAT traversal settingsStep 3Set the fields as described in Table 5-15 on page 60.Table 5-15 Configuring NAT-related settingsFi

Configuring Dynamic Ports When a firewall is crossed, the firewall administrator must open a range of dynamic TCP andUDP ports to allow bidirectiona

Step 6Select Save.Configuring Quality of Service (QoS) Quality of Service determines how your network handles IP packets sent to your system duringa

Figure 5-24 Configuring QoS settingsStep 5Set the fields as described in Table 5-17 on page 63.Table 5-17 Configuring QoS settingsField Name Descripti

To do this, the gatekeeper must register all endpoints to maintain the mapping list of aliasesand endpoints to successfully route calls. It also regis

The SCOPIA XT4000 Series provides cost-effective true HD 720p videoconferencing at 60fps with the impressive price performance. It is a new innovative

Figure 5-26 Configuring the Gatekeeper settingsStep 8Set the fields as described in Table 5-19 on page 66.RADVISION | Installation Guide for SCOPIA XT

Table 5-19 Configuring the gatekeeperField Name DescriptionUse gatekeeper Enables/disables the use of a gatekeeper. If No is selected, allthe other fi

Configuring SIP Server Use The SCOPIA XT Series can be configured to function in a SIP environment, where aliases aremanaged by SIP servers rather t

Figure 5-27 Configuring SIP settingsStep 3Configure parameters as described in Table 5-20 on page 69.RADVISION | Installation Guide for SCOPIA XT4000

Table 5-20 Configuring SIP-related parametersParameter DescriptionUser Enter the system user name (alias). Thesystem is registered to the SIP Registra

other benefits like remote centralized upgrading and backing up of all endpoints in your videonetwork.In deployments without iVIEW Management Suite, y

Figure 5-28 Configuring LDAP settingsStep 3Select Add Server.Step 4Configure LDAP server settings as described in Table 5-21 on page 72.RADVISION | In

Table 5-21 Configuring LDAP server settingsField Name DescriptionType Allows to define the LDAP server.Address Indicates the LDAP server address.Port

Configuring Call Settings This procedure shows how to configure the system for support of incoming and outgoing calls.To configure the call settings

Figure 5-30 Configuring general call settingsStep 7Set the fields as described in Table 5-23 on page 76.RADVISION | Installation Guide for SCOPIA XT40

Table 1-1 Differences in features for models in the SCOPIA XT SeriesFeature SCOPIAXT1000PiccoloSCOPIA XT1000and SCOPIAXT1200SCOPIA XTTelepresenceSCOPI

Table 5-22 Configuring general call settingsField Name Description<auto> This is the default setting. It indicates that the system tries tochoos

Table 5-23 Configuring the IP-related call settingsField Name DescriptionDTMF RFC2833 (H.323) DTMF describes a method to send DTMF inside anaudio stre

Step 5Set the fields as required.Step 6Select Save.Configuring Video Compatibility with Older Systems Some older endpoint may be not fully compliant

Step 5Set the fields as required.Step 6Select Save.Securing Calls The system can manage secure videoconference sessions via encrypted connections, in

Step 5Set the fields as described in Table 5-24 on page 79.Table 5-24 Configuring settings for securing callsField Name DescriptionAccept protected ca

The SCOPIA XT Series provides video technology for room conferencing, including support fordual stream 1080p video, high quality data sharing, high qu

Table 6-1 Bidirectional Ports to Open on the SCOPIA XT SeriesPort Range Protocol Destination Functionality Result of BlockingPortRequired69 TFTP (UDP)

Port Range Protocol Destination Functionality Result of BlockingPortRequired3338 XMLCommands(TCP)SCOPIA Control,SCOPIA XT DesktopServerEnables communi

Table 6-2 Outbound Ports to Open from the SCOPIA XT SeriesPort Range Protocol Destination Functionality Result of Blocking Port Required162 SNMP (UDP)

ProcedureStep 1Select Administrator > Settings > Network > Preferences > Dynamic Ports.Step 2Modify the TCP base port in the Ports field.

There are a number of ways that the SCOPIA XT Series can be deployed in a network,depending on its use as a room system endpoint, a conference hosting

NoteYou can configure the base port to any value between 1024-65535. The number ofports is calculated automatically by the system. Step 6Select S

www.radvision.comAbout RADVISIONRADVISION (NASDAQ: RVSN) is the industry’s leading provider of market-proven products and technologies for unifiedvisu